Ensuring your Holosun EPS Carry Red Dot sight operates perfectly requires occasional factory resets. This process clears any custom settings, returning the sight to its initial state. Do you need to perform a reset, follow these easy steps for a successful outcome.
- Begin by locating the small lever on the rear/left/bottom of the sight.
- Press and hold this button/switch/lever for roughly 5 seconds.
- You will see a series of flickering/flashing/blinking lights indicating that the reset process is underway/in progress/happening.
- Let go of the button/switch/lever once the lights have settled.
Your Holosun EPS Carry Red Dot is now reinitialized to its factory settings. You can thereafter proceed with adjusting your sight according to your needs.
Reset Your Holosun EPS Carry to Factory Settings
Occasionally, you/your/one may need to reset/restore/reconfigure your Holosun EPS Carry to/back to/at its factory settings. This can be helpful if you/your/it are experiencing performance/operational/system issues or simply want to start fresh. To perform/execute/carry out a factory reset, first ensure/make sure/verify your Holosun EPS Carry is powered off/switched off/turned off. Next, locate the reset/factory reset/configuration button on the side/rear/bottom of the device. Press and hold/Depress and maintain/Tap and sustain the reset button for approximately 10 seconds until the display flashes/shows a message/indicates completion. Release the button, and your Holosun EPS Carry will now be reset to/returned to/configured at its factory settings.
Return Your Holosun EPS Carry To Default
Needing to adjust your Holosun EPS Carry settings? Setting back it to the factory default is a simple process. First, locate the small button on the side of the sight. Next, squeeze this button for approximately seven seconds. You'll know it's reset when the dot blinks. Your Holosun EPS Carry is now back to its original factory settings.
Restore Your Holosun EPS Carry Red Dot
To initiate a hard reset on your Holosun EPS Carry Red Dot sight, you will need to locate the minute reset button situated on the side of the device. Using a pen tip, gently press and hold the button for approximately five moments. While holding down the button, turn the power switch to the "on" position. Continue pressing and holding the reset button until you see the red dot pulse rapidly, indicating that the hard reset is complete. Release the button and your Holosun EPS Carry Red Dot should now be fully reinitialized.
Restoring for Holosun EPS Carry Sight Users
If you're facing issues website with your Holosun EPS Carry Sight, a factory reset can often address the problem. This process wipes all settings and returns the sight to its initial configuration. Before performing a reset, it's essential to review your sight's user manual as the exact steps may vary slightly depending on the specific model.
Generally, you'll need to enter the sight's settings menu and then locate the factory reset feature. Once selected, the sight will request you to confirm the action. After the reset is successful, your EPS Carry Sight should be back to its factory settings and ready for setup.
Remember, a factory reset will erase all personalized settings, so it's recommended to record any important configurations before proceeding.
Reset Your Holosun EPS Carry Red Dot to Factory Settings
Performing a factory reset on your Holosun EPS Carry red dot sight can/may/should sometimes be necessary. Whether/If/Because you've encountered issues with the sight or just want to start fresh/begin anew/return to defaults, this procedure is relatively straightforward.
- First/Initially/Begin by ensuring your red dot sight is turned off/switched off/disabled.
- Locate the tiny reset button on the side or bottom of your Holosun EPS Carry. It's usually a recessed button/switch/lever.
- Using/Employing/Leveraging a small, pointed object like a paperclip, gently press and hold the reset button for approximately 5-10 seconds.
- You'll likely/probably/possibly notice a change in the red dot display, indicating that the reset process has started/begun/commenced.
- Release/Let go of/Withdraw the button and your Holosun EPS Carry should now be back to its factory settings.
Remember to refer to your user manual for specific/detailed/precise instructions on resetting your particular Holosun EPS Carry model.